Biteman High- precision Filter -The Innovator in the Filter


Biteman high precision filter is mainly used for filtering impurities of solid particles in the compressed air, and it has a certain blocking effect for liquid water and oil, changing the traditional filter structure and method.


High precision filter mainly consists of the inlet, outlet chamber, outlet, open filter cartridge, storage liquid chamber, sewage-outfall and other components.

Filter cartridge consists of inlet end, high-molecular polymer, filter cartridge in-wall, the discharge end and other components.


The filter uses open design, making filtered impurities directly pass liquid storage cavity, without permeation by filter element, and discharge by automatic drainage valve; the middle filter element uses high-quality polymer filter material, it has a certain adsorption capacity for oil mist and other impurities, and fully ensure filter effect; part of the compressed air is going to purge inner wall of the filter from top to bottom, making filtered impurities effectively eliminate, while reducing the resistance of filter cartridge for compressed air.


Traditional filter element will be blocked at the lower end of the filter, filtered impurities of compressed air will gather inside of filter element, and penetrate into the bottom of filter chamber by filter element, and then discharge through automatic drainage device.


Filter selection

During selecting filter, some people have misunderstanding that the air quality just selects single filter to meet the requirements with corresponding processing accuracy, it will save money. In fact, although it depends on Single-filter processing accuracy decision, high-precision filter will soon be blocked due to excessive load, speeding up replacement frequency of the filter element, which will increase production cost, if no pre-treatment protection of pre-filter (much lower level).


The filter requires that periodically replacing filter cartridge

It will cause gas flow becoming smaller and pressure drop becoming high in the system as for filter cartridge continues to be contaminated. At the same time, energy consumption of the electricity will rise as well, resulting in increasing operation and production costs, increasing environmental burden. Thus the filter cartridge needs to be replaced regularly.



Precautions of Filter installation

1. The working pressure does not exceed indicated maximum pressure of the filter;

2.The filter is generally installed behind after-cooler and gas storage tank, and then close to use point and lowest temperature point as soon as possible;


3. The filter should not be installed behind the quick opening valve, and prevent the back-flow and impact phenomenon;

4. The filter should be installed vertically, and leave enough space to replace filter element in the bottom of the filter;

5. The larger filter should be properly supported in the pipeline.



Instructions on replacing filter element

1. Isolate filter, close inlet valve or compressed air supply system, close outlet valve after completely depressurizing (or close outlet valve through filter drainage);

2. Remove the shell; take down old filter element;


3. Clean filter housing;

4. Put on a new filter element (do not leave out seal ring, and add Vaseline, the filter should be installed tightly and properly).


This article from www.bitemantech.com by muriel.zhou

评论

发表评论

此博客中的热门博文

Modern Planning in the Field of Compressed Air

图片
In the past, people only consider the initial investment and operating energy costs such as some simple economic factors, they often overlook the influence pollutants in the compressed air for system when established a compressed air system , thus ignoring the compressed air quality (it can not reach standard will bring huge invisible waste for enterprises), and these losses are often much higher than the high quality purchase and operating costs of purification equipment. Perhaps many companies believe that compressed air equipment just little impact when select ordinary one, but what will actually appear on us? In the 1980s, the industry lagged far behind today, the developed countries put forward ISO8573 standards for the purity of compressed air as for different gas equipment, while it failed to supply the gas equipment standard of compressed air, which caused serious impact, such as shorten the service life, decrease accuracy, increase failure rate, poor quality, and the safet
阅读全文

The Importance of Brand Awareness

图片
Brand is an invisible asset for the enterprise, it’s also the most valuable wealth. in the rapid development of the modern life, the difference become shrinking for product performance, quality, sales service from different enterprises, so the brand will become the main factor to choose products for consumer. "Stupid businessmen sell products, smart businessmen sell brand" This sentence fully illustrates the importance of the brand for the enterprise . therefore, companies should have enough brand awareness, and strive to run the business brand. it is the core content of the product, and brand awareness isn’t all other means of marketing, such as Atlas, Ingersoll Rand, Sullair, Kobelco, etc. these enterprises prefer to brand recognition rather than products identification , and it’s also become the only element of market choice. Brand not only refers to the product quality, but also includes the appearance, technology, function, utility and others, it need long-term accumulat
阅读全文

“Throw a sprat to catch a herring" to get the maximum benefit in a short period

图片
There is a question, why do we establish business? Companies just considering saving cost regardless of construction of enterprises, but it real should need the cost of consumption. later hear a manager says to the subordinate, " I have to find ways to earn back for company spent every penny", perhaps this is a lot of top management staff thought, which is good point for a top manager, then we will be reach the business target to obtain the greatest benefits in a short period.  It is not so easy to realize how to get the maximum benefit in a short period. such as a lot of leading brands seem to be impeccable, while the leading brand's business is far less flexible than some small businesses for imbalanced development of different regional market, much longer product line, and imbalanced development in different products. it is difficult to develop appropriate products and marketing strategy according to local conditions due to consider the national market. I
阅读全文